You must first be logged in to post a new topic.If you are not registered, please click "Create Account".
Pages: 1 [2] 3
To install drywall on the ceiling and walls of a framed room, you will need an assistant, especially for the ceiling.Quick tips for Hanging Drywall:1. Construct a pair of T-braces from 2 X 4s about an inch longer than the distance from floor to ceiling. Nail 2 X 4s about 3 feet long to one end of each longer 2 X 4 to form the Ts. Alternately, adjustable T-braces can be rented.2. Cut drywall panels to size. Use a sharp utility knife along a straightedge to cut drywall. After you make the cut through the face paper, place the board over a length of 2 X 4 laid flat on the floor, or some other type of support, and snap the scored section down.3. Install drywall panels on the ceiling. If possible, try to span the entire width with a single sheet of wallboard to reduce the number of joints.4. Drive nails at 6-inch intervals into all the joists covered by the sheet. Start in the center of the drywall panel and work out.5. When the ceiling is finished, cut and install wall panels. Carefully measure for any cutouts in the drywall, including electrical outlets, switches, or light fixtures.6. Space the nails 6 inches apart along studs, but start nailing 4 inches from the ceiling. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Comments (0)
Older homes often have plaster walls. Plaster is both a durable and good-looking surface. There is, however, one drawback. Plaster inevitably develops cracks.Latex paint will hide hairline cracks in plaster, at least temporarily. The coverup, though, may last only a few hours or a few months. Small plaster cracks have an annoying way of showing up again and again. It may be smarter to enlarge them and fix them properly once and for all.Making a small flaw bigger may sound like reverse logic, but it’s easier to fix big cracks in plaster than small ones. Use plaster of paris, which doesn’t shrink as it dries, or purchase premixed plaster repair compound.Here are the tools you need for repairing cracked plaster:* Utility knife* Vacuum cleaner* Plaster of paris or premixed plaster repair compound* Paintbrushes* Scraper or trowel* Wood block* Medium- or fine-grade sandpaper* Primer and paint4 Effective steps are mentioned below..1. Prepare the Crack2. Mix and Apply Plaster3. Sand and Let Dry4. Sand, Prime and Paint -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Plaster is the covering given to construction, and for this reason it is needless to say that plastering should be done correctly.(For more information on what plaster is, see previous blog) Here are some guidelines while repairing plaster:1. Fill tiny holesYou can use a putty knife to apply spackling compound, available in small cans for touch-ups. Let dry. If the first coat shrinks as it dries and leaves a slight indentation, apply a second coat.Next, sand lightly with fine sandpaper and touch up with primer and paint.2. Repair loose plasterRemove any small, loose chunks of plaster and patch the holes. For large, loose areas, install the washers in concentric rings, starting where the plaster is firmly attached and working inward. Cover the area with joint compound.To reinforce plaster along large cracks, install screws every 6 inches on both sides of the crack and about 1 inch away from it. Drill pilot holes with a 1/8-inch masonry drill bit. Cover the area with joint compound.3. Mix compoundUse a setting-type joint compound such as Durabond 90 for all repairs other than those dealing with only tiny holes. Mix the compound in a bucket with water according to the directions. Depending on the quantity, use a potato masher, paint-mixing drill attachment or paddle mixer.4. Fill holes and areas where plaster is missingFill a hole with compound to within 1/8 inch of the surface using a 6-inch spackle knife. Then scratch the wet compound in a crisscross pattern with the edge of your knife. When the scratched coat dries, apply a leveling coat.For larger areas of missing plaster, measure a piece of drywall to fit the hole, cut the piece out with a utility knife, then screw it to the lath. Apply the compound in two stages and extend it about 2 inches onto the surrounding surface.Apply two or three additional coats of compound, allowing complete drying between coats and feathering each coat over a wider area than the preceding one.Use a pole sander or a similar pad sander with very fine sandpaper to smooth the compound after it has dried.5. Repair hairline cracksApply a thin coat of compound on the wall along the crack. Embed paper drywall reinforcing tape in the compound immediately and smooth with a spackle knife. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
For those of you who do not know, plaster is a hydration product used as a building material, like cement. Plaster is a starter. It is a dry powder which, after being mixed with water, forms a paste which later hardens.Why is plastering required for your home?Home interior and exterior plastering is very important. It protects the entire structure from various temperature variations. It’s basically a shield that protects your wall from the external attacks of chlorides, sulphates, etc.What are the precautions?Some basic precautions should be taken while plaster work is being done. Generally plaster should be used indoors only and in areas that are not damp. Plaster should be mixed with clean cold water and the plaster should always be added to the water. It is recommended to use the minimum amount of water at the time of mixing. Always use cement that releases low hydration heat, like blended cement. Before plastering, the surface should be wet. After plastering, tend to the surface for at least 9 to 11 days. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Drywall is a common building material which is typically made up of a layer of gypsum plaster pressed between two thick sheets of paper, then dried. Drywall is used globally for the finish construction of interior walls and ceilings. Drywall is also sometimes known as plasterboard, sheetrock, or gypsum board. Drywall covers interior structures like beams and joists and provide a flat surface for papering or painting. It can be used for both interior wall surfacing in new home construction and in existing home repairs and renovation. The name Drywall came about because of the fact that it went on dry rather than wet like plaster.We at Precision Painting Plus provide drywall services in Long Island and the Five Boroughs of New York. We take on every custom job whether it is small or big! Just watch how we transform your wall and make it look clean, fresh and new in no time! We care about our customer’s homes, and therefore guarantee that everything will be protected before and while all drywall processes are going on. We have experienced professionals who will help you out, no matter your budget. We are licensed and well insured to protect you, and we provide a complete job site cleanup after each job! -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Painting the exterior of your home can be a real headache! The exterior of your home is like a shield, and in order for it to remain useful you must take special care of it. If your house suffers from a number of surface problems like peeling, cracking paint, mildew, mottling, etc. then you must act fast and fix the issue.Before starting an exterior painting job, one of the most important things to do is surface preparation.Some effective ways are mentioned below…-Always plan a project from start to end before beginning it.-Measure the exterior of your home.-Stay aware of local weather before starting a job, as an exterior paint job should not be started during rainy weather. Doing exterior painting during rain or rainy weather can wash away the color.-Make sure your home is ready for painting and there are no pre painting tasks needed to be done.-Select the kind of paint which you want to use for the exterior of your home, and then choose a color or multiple colors which you will be using.-Prepare the surface – this involves repairing cracks and cleaning chalky surfaces. This also includes removing rust and other factors.-Assemble all tools and equipment you will need for the job.-Prepare the yard – Cover up your benches, garden, and any other things you may have in your yard.-Use a power washer to remove loose paint. Also remove loose paint by sanding and scraping.-Clean the surface, and then dry it before starting the job.-You are now ready to apply the first coat. Keep in mind to reach high points of your home you will need a ladder. Be extremely careful when using a ladder. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Wallpaper can be a great alternative to painting. It changes the dynamic of a room in a very different way than just solid paint. It does this by adding texture, pattern, and multi-dimensional color to your living space. Now that wallpaper installation is no longer a difficult and time consuming product thanks to technology, wallpaper is becoming more popular again.Wallpaper shopping can be a confusing process due to the difficult terminology that exists within the industry. For this reason, I will take you through some of the common terms in the industry to make the process a little bit easier for you.Washable – This means that this wallpaper can withstand the occasional sponging with a mild detergent. This is a useful feature in bedrooms, living rooms, dens, dining rooms and laundry rooms.Scrubbable – This term means that this wallpaper can withstand scrubbing with a brush and mild detergent. You will find this to be particularly useful in high traffic rooms such as kitchens and bathrooms.Stain Resistant – This term indicates that this wallpaper will show no change in appearance after the removal of stains caused by grease, beverages, handprints, etc.Prepasted – This means that the wallpaper comes from the factory with a backing that is treated with an adhesive that is activated when it is dipped in water. Simple, it means no additional paste is necessary to purchase.Paperbacked Vinyl – This term in the industry refers to wallpaper that has a top layer of vinyl and an under surface of paper. It is washable and peel able.These are the most common terms in the wallpaper industry. Now that you know the meaning of these terms, you can purchase the best wallpaper for your job, and hire a professional to do the rest! At Precision Painting Plus, we use up to date techniques and our wallpaper professionals deliver precise results every time. We do this by making sure we properly prepare the walls for installation, and perfectly cut each sheet to fit each individual wall. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Texture wall painting offers huge potential for creativity and can really give a completely new style to your walls. It can be customized uniquely for different rooms and is more cost effective than wallpaper. In fact, one bag of textured paint can be used over an area covered by double the amount of wall paper. Textured paint is also preferred over plain wall paint for the obvious reason; it is more exciting and lively.Different textures can even be created by using simple household items. Whisk brooms, for example, can be used to create glass cloth like textures. Long strokes of a brush can also create a splashing texture. You can also be creative in using sprays and different rollers to create visually interesting and unique combinations. Another example would be using combs to create lines or to just paint the wall with thick paint in up and down strokes, and then using towels to swirl the paint around creating a round peak and valley texture. The other types of textures (like wood grain) can requires different kinds of tools and may take some practice and creativity. Textures can be achieved with glazing, or sponge dabbing, etc.There are definitely benefits to having textured walls. Besides looking creative and attractive, textured paints can be used to cover up old fashioned paneling and give new looks to an older home. Another plus is that most textured paints are water soluble and can later be softened and repainted by pain paints, if desired.Lastly, textured paint can also cover up imperfections in the walls and hide improper or uneven drywall. For most homeowners, imperfections in the walls are noticed after a few years, and fixing them up can sometimes be very expensive. Texture painting, as mentioned above, can easily camouflage any uneven rises and even cracks that are just beginning to form. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Faux painting or faux finishes are one of the latest trends in home décor these days. They bring dimension and prestige to any space, and are available in a wide range of finishes. There is no doubt that you will be able to choose the perfect faux finish for any room!Here are tips that will be suitable & effective for your faux painting job:-There are so many tools for faux painting available in the market. Some which work, and some that don’t. For faux painting simpler is best.- For each faux finish or technique, different paints and tools will be required. For this reason, it is important to be sure of what type of finish you want before getting any tools or paint product.- Always use branded paint product.- Aside from choosing paints, you must also choose glazes to use. Before doing either, see real life examples or catalogs.- In order to achieve your desired result, preparation and practice is very important. Before beginning your job on permanent surface, practice the paint techniques on a board or any spare solids. This way you will get a chance to perfect your faux technique and also will allow you to get a preview of the colors you have chosen, before beginning anything permanent.- Make sure to fix up the walls and fully prepare them before beginning the job. Apply a base coat of primer once the wall is prepared.Finally, no matter what type of faux finish you want to create, take a look at real life examples before you pick up the tools or paintbrush, refreshing your memory before you begin. This will help you generate ideas and techniques you might have overlooked otherwise. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
When it comes to interior design, the first thing you need to do is really think about what your ideal room is like. To really get the best ideas and bring your thoughts to life, you should learn how to properly brainstorm.Quick Tips are below: Sit somewhere with no distractions, think over everything you already know you want and start jotting down ideas.Start sketching whatever you are seeing in your mind and visualizing. You can also get ideas from books&magazines.Look at fabric, color and flooring samples. Also look at photos of the existing space and the items you are going to keep.Pick out things that catch your eye & put them all together. Then start again over. You should continue this process a few times until you run out of ideas.See what idea or scheme catches your eye. Ask yourself – What caught your eye and why? What should be the focal point? Will this work the way you want it to? Basically it is like a flow chart. If yes, then keep working on it. You should look for other items and accessories also that coordinate with it. If no, then go back and find another idea and start working with that.You may have come up with an even better idea of your own for brainstorming. This is a catalyst for creative thinking. The fact is you have to VISUALIZE what things will look like when the project is finished.The stronger your visualization is, the more ideas will come. -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
Everyone knows that painting a room is important when you are looking to improve the look and the value of a room. However, not everyone knows how to correctly do so. If you choose to do this work yourself rather than hire a painter, you should definitely know where to start.When painting a room you are always going to paint the ceiling first. Ceilings and walls are the easiest surfaces to paint, and using a proper roller you can apply paint very quickly and efficiently. You should use an extension handle for the roller when trying to reach the ceiling. We suggest wearing goggles when working overhead with a roller to protect your eyes from paint drop. If you are using a ladder instead, make sure that your paint try is attached to its utility shelf. Go slowly with the process of painting with a roller. The faster you move the roller, the more paint is likely to spray off of the cover. Always also try to do this job during the day because natural light is the best for interior paint jobs. You should also always work in small sections at a time, as it reduces the possibility of visible roller marks on the surface before it is completely painted.After the ceiling is completed, you can begin wall painting. First paint the outlines of the walls and ceiling with a brush. Use different brush angles to paint narrow edges or corners. Start with a diagonal stoke followed by back-and-forth strokes. Use your roller to smooth the brushed paint, and then apply vertical and horizontal strokes.And that’s it! -------------------------------------------------As always, Enjoy painting!Any Questions Call us at 888-615-9933!
If you are planning to use a paint roller for painting walls in a room, the first thing to do would be to get your equipment. Not only do you need paint rollers, but you should probably have an extension pole as well, and of course paint roller pans. Because you will be pressing on it pretty hard, we suggest buying a strong roller frame. Get one with a threaded end in the grip so that you can add the extension pole. Then pick the right sleeve for the job. Generally smoother walls take a shorter nap and heavier textures, such as plaster, need a longer nap.Paint rollers plan an important role in painting jobs. Paint work with a roller is less exact than paint work with a brush, and is therefore much more comfortable for a novice painter.Visible roller marks is one problem that can occur when using paint rollers. These roller marks can occur for one of two reasons: either the roller face was not fully loaded with paint, or the paint on the roller was not spread equally. To avoid this, make sure you follow the correct steps to load the paint.To paint with a paint roller you should first moisten the roller with water for latex paint, or the appropriate thinner for different types of paint. You should then roll out the extra moisture on a piece of craft paper or scrap lumber. It is not advised to use newspaper because the roller may pick up the ink.After this is done, you should fill the well of the roller pan about half way full, and set the roller into the middle of the well. Next, pick up the roller to roll it down the slope of the pan. Stop just short of the well. You will have to do this process two or three times to allow the paint to really work into the roller. In addition, once it is done you should dip the roller into the well once more. When this is completed, roll the roller on the slope until the pile is well saturated.We suggest that while painting a wall, the first stroke should be up. This is because if you roll down on the first stroke, the paint might puddle under the roller and run down the wall. In addition to that, be careful not to rapidly use the roller across the wall because the centrifugal force will cause it to spray.The most effective method of painting with a roller is to paint 2 or 3 square foot areas at a time. First roll the paint in a zigzag way, without lifting the roller from the wall. After that you will fill in the blanks with more vertical and horizontal strokes. To finish the area, use light strokes that start in the unpainted area and roll into the paint. At the ending stroke, raise the roller from the wall slowly so that it does not leave a mark. Continue this process in the next unpainted area, and continue until all areas are completed. Make sure to always start a new area from the below ending edge. You should also be sure to smooth the new application and blend it into the previously finished area.Enfold the roller sleeve in foil or plastic wrap or immerse it in water (if you’re painting with latex) if you are going to discontinue painting for more than a few minutes.After finishing make sure to clean both the roller frame and the sleeve well if you want to use them again. Press as much as you can to paint out of the sleeve. Then wet, squeeze, and wet until the liquid (water or solvent) is pretty clear. -------------------------------------------------As always, Enjoy painting! Any Questions Call us at 888-615-9933!
When it comes to painting your home, there are many important painting tools out there. One very important one often used is a paint pad. Paint pads are helpful in applying paint in hard to reach places. Most pads are made of synthetics materials or plastic foam, and are suitable for both latex and alkyd paints. The end result of interior painting depends on whether or not the preparations were efficient, and for that reason it is important to know the right techniques. By using the right techniques and the right strokes, you can get a fantastic finish.Some important tips while using a paint pad:1. First, of course, you must purchase the paint pad. The plastic of the kits can be used as the paint tray and as an airtight lid.2. Hold an empty tray on your hand with the right side up. Next hold your tool properly and stick tape down one side of the tray if necessary.3. Bring it lightly behind your palm and up to the other side of the tray. This will ensure the existence of the tray in place while you are working.4. Hold the painting pad firmly and paint exactly at eye level in front of you. This way you will see what you are doing and will have good control of the paint pad.5. While using painting pads with a tracking wheel, tape off the trim of the wall or ceiling. This is because when you apply paint on to the pad, paint can get on to the wheels and leave marks on the trim.6. Next, reload the paint pad and repeat the process after reasonable time, preventing the pad from drying.7. Spread and apply the paint on with long strokes.8. If you are planning to take a break from painting, store the pad inside the tray and shut the lid to prevent the paint from drying.9. Load paint on the paint pad. This will ensure that there is no overloading of paint or sinking of the pad into the paint.10. Wriggle the pad to get the paint on to the foam and bristles. This movement will not only load the paint but lock it in.11. To remove extra paint, move the pad gently across the edge of the tray.12. Apply the full pad firmly on the surface and move in one direction to deliver paint to the surface. Your next stroke should be on the same area in the opposite direction to fix the paint and remove bristle marks. Paint briskly, working from one side to the other.Following these steps should definitely give you a great end result. -----------------------------------------------------As always, enjoy painting!Any Questions? Call us at 888-615-9933
Wall stickers are one of the latest trends in home décor these days. Basically, wall stickers are sticky pieces of paper that generally have some sort of pattern on them. Wall stickers are easier and more unique than wallpaper. They come in different shapes and sizes, and allow you to add dimension and prestige to any space. They are available in a wide range of finishes, meaning you can no doubt find the perfect wall sticker for any room.Wall stickers are made up of an adhesive material that can be easily places on any kind of surface. They do not leave nasty marks on the walls, and are not likely to quickly wear off. Wall stickers allow you to decorate your home without a great deal of effort and skill. There are even many pre-set deisgns available in the market. You can also put in requests for wall stickers to be personalized according to your own personal preferences.Wall stickers are effective in adding detail to your walls or ceiling, and can bring life and dimension to your room. They are affordable and stylish – and for those who like to change things up a lot, they can be easily changed!Wall stickers provide a fresh look to your rooms and can even change your mood. Wall stickers can be used virtually anywhere – whether in a bedroom, nursery, kitchen, office – or anywhere else you can think of!-----------------------------------------------------As always, enjoy painting!Any Questions? Call us at 888-615-9933
A person’s bedroom is their private heaven. It is a place where they can be themselves and relax after a busy day. For this reason, it is very important to have a room that can really put you in a good mood and put a smile on your face. Adding some color and using design techniques can really transform your bedroom. When deciding on bedroom colors, you can think about warmth, style, mood, and comfort.We at Precision Painting Plus offer you a range of different color schemes that can make your private room look attractive and unique. But the first question is all on you: What do you want? What do you really want your bedroom to look like? Do you want it to be romantic, relaxing, fun? Once the objective is clear, you can move on to choosing the colors accordingly.Some color ideas are given below..Muted and Bold ColorsMuted colors are primary or secondary colors mixed with grey, toning them down a bit. These wall colors tend to give a soothing ambiance to the room. The calm and relaxing tone help with a good night sleep, and as an added benefit, muted colors can make a small room appear big. An alternative to muted colors would be going for the opposite feel – a livelier look to your room. This can be done by using bold colors on your walls.Cool ColorsThe hues of cool bedroom colors are perfect for any age group and go wonderfully well in bedrooms. The colors tend to give a calm and peaceful feel to a bedroom. These colors are often the most popular choice for bedroom colors. Some colors that fit into this category are blues, greens, and lavenders. If you have a smaller bedroom it is best to go for a lighter color as compared to darker shades.Warm ColorsAlthough cool colors are a more popular choice, the right combination of warm hues can give your room an equally pleasant look. Most people give a warm look to their bedrooms by applying yellows, peaches, or light pinks. Using the darker shades of these warm shades, however, will overpower your bedroom.Neutral ColorsNeutral shades also often ten to work out wonderfully on bedroom walls, giving an elegant and calm look. These colors can give character to your room, even with simple little changes.The bedroom wall colors speak for themselves. The mood you have in mind should be reflected in your bedroom. For example, if you are going for blue walls then it is going to give a soothing and calm feeling to your bedroom. Although it is not feasible to repaint your room every month, you can always change up the room whenever you’d like by changing the décor and moving around the furniture.No matter what your choice of bedroom colors may be, make sure to always try to add a personal touch to really make it YOUR bedroom.-----------------------------------------------------As always, enjoy painting!Any Questions? Call us at 888-615-9933
When it comes to painting a room, preparation is half of the battle. You should know everything about interior painting preparation before starting a job. There are a wide variety of interior paints available these days, so knowing their respective uses is very important. There are paints available for every surface, and using the wrong type on the wrong surface can cause you to damage the surface. That being said, first thing you should know is which surfaces are ideal for a given paint.Fortunately for homeowners looking to do the work themselves, modern paint technology has taken a lot of the risk out of choosing the proper paint. Latex paints have been improved to withstand dirt, moisture, and daily wear and tear. They are now washable and durable.Still a vital factor remaining is your color preference. The colors you put in the walls of your home should fit your personality, as well as the theme or purpose of the room.Some quick tips for interior painting prep are mentioned below.- If you are going to paint over a previously painting surface, make sure you notice and take care of any peeling, rough or chipped areas first.- Move all furniture out of the room if possible – this is the best way to find flaws.- If not possible, move all of the furniture to the middle of the room and cover them.- Take down any draperies.- Remove all light fixtures.- Remove the wall plates from any electrical outlets and switches.- Wash the entire room.Now you’re ready!-----------------------------------------------------As always, enjoy painting!Any Questions? Call us at 888-615-9933
We all know that paint brushes play an extremely important role in painting a room. What you may not know is what type of brush is the right one for your job.Choosing the right brush for you job makes the job easier and the results superior. Home painting brushes come in a variety of shapes, sizes, and materials.Paint brushes can be flat, oval, or angular. They range in sizes generally from 1-6 inches wide.Each brush has its own use. Every project you do will generally require two brushes – one for general use (large areas) and another for the finer details.With surfaces that have many angles, and angular brush is very handy. In cases with narrow surfaces, a multipurpose brush can be used. Flat and oval shaped brushes can be used for all surfaces.Certain paint brushes are best for certain tasks and this is something that is very important to consider before painting.For the general painting a good size brush to use is one that is 3 inches, whereas for a finer narrow finish a good size to use would be 1 ½ inch brush. For basic cutting a 2 ½ inch brush is commonly used, and for small trim a 1 ½ inch brush is recommended.Here are some other brushes to use in certain circumstances: 1. For small surfaces such as touch-up, trim, moldings and window sashes 1-2 inch brush is a good choice.2. For general cutting in of walls as well as all exterior trim 2-3 inch brush works great.3. For large areas such as back brushing behind an airless sprayer or applying stain to a deck floor 4-6 inch brushes are perfect.--------------------------------------------------------As always, enjoy painting!Any Questions? Call us at 888-615-9933
Painting a room on your own can be a difficult task. The number one thing to know in order to paint a room is how to correctly use a paint brush.To properly use a paint brush, three steps are involved: Brush loading, Paint application and distribution, and paint smoothing.Here are some quick tips…Step 1: Loading the Paint BrushFirst things first: There IS a right way to load paint onto your brush. You can either use paint from the paint can or pour some paint into a painting pail.Always carry paint with you as you paint when using a paint brush. To do so, use the paint can handle and/or paint pail.Dip the brush directly into the paint up to 1/3 of the length of the bristles. This prevents overloading of the brush, and therefore helps prevent dripping.Always tap both sides of the brush lightly against the side of the can or pail.Do not scrape the paint off of the brush by dragging it across the edge of the bucket. Doing so removes the paint and makes the brush ineffective.Step 2: Applying and Distributing Paint on the WallGenerally, for a large flat wall you should use a paint roller to apply the paint. As for cutting in, which is painting the corners at walls/ ceilings and around baseboards/trims, you should use a paint brush.If you are right handed, cut the wall at the ceiling corners from left to right, giving you visual control over how well the paint is flowing. If you are left handed, do the opposite.Press the brush against the wall just enough to flex the bristle, and always use the narrow edge of the brush when cutting in.If you are painting a larger wall area, you should not be using the same technique. In these situations, you hold the brush at about a 45 degree angle, painting in several diagonal strokes. Again, press the brush against the wall just enough to flex the bristles. Distribute the paint on the large flat area with horizontal strokes.Step 3: Smoothing Out the PaintOnce the paint is applied and distributed on the wall or ceiling surface, the next step is to smooth it out. At the end of each stroke, lift the paint brush from the surface.Once the job is done, wash the paint brush properly. After drying, take plastic wrap and tightly wrap the brush bristles. -------------------------------------------As always, Enjoy painting!Any questions? Call us at 888-615-9933
One of the important aspects of a successful paint job is keeping things clean. After finishing a painting job it is important to clean the area and equipment.Here are some specific tips on keeping things clean while doing a paint job!1. Minimizing Spatters&Drips;If you are using a roller, avoid bumping the roller into the walls as you paint the ceiling, or into the ceiling as you paint the walls.No matter how fast or slowly you move the roller across a surface, just wear a cap and make sure the furniture&floor are covered with drop cloths. You can use canvas drop cloths as they are durable, washable, and reusable. You can also use plastic drop cloths, which are less expensive.To prevent paint drop from occurring on windows and doors we recommend using paint shield. Hold the shield in one hand and place it perpendicular to the surface being painted, while applying the paint using your free hand. Paint shields are ideal for painting window frames because they can be used to keep the paint off of the glass.Some spatters and spills are inevitable. We advise you to keep a moist sponge and pail of water available when you are using latex paints to wipe up any spatters or drips that may occur. If you are using a solvent-thinned paint, keep thinner and a supple of rags nearby to wipe up any of the spatters or drips. Always make sure to wipe them up right away before they dry into bumps.2. Cleaning Windowpanes, Spatters, and DripsThe best time to clean up paint drips and spatters is when they are still wet and will wipe away easily. Also, if you used masking tape around any windows, peel it off right after painting. Waiting too long to do so may cause you to accidentally pull off some of the paint.Cleaning up drips and spatters on most other surfaces is easy and less time consuming. For latex paint, a soft cloth combined with household detergent and warm water should do the trick.To get paint drips off hardwood, ceramic tile, or resilient flooring, wrap a cloth around a putty knife and gently scrape them up. Next, wash the areas with warm, soapy water.3. Cleaning Painting EquipmentNow clean your paint equipment. This includes not only rollers and brushes but also reusable drop cloths, paint cans, containers and roller pans. Don’t delay cleaning your equipment, as fresh paint comes off the easiest.To clean paint color from reusable drop cloths of heavy-duty plastic or canvas just use water, soap and paper towels. Do not use solvent on drop cloths.As always, enjoy painting!
Through experience, I have found that many homeowners love the look of wallpaper. It covers imperfections on a wall, while at the same time adding unique patterns and textures. Wallpaper created a finished wall surface that is very difficult to replicate with paint. Quality vinyl wallpaper that is professionally installed can last up to 15 years with little to no maintenance necessary.A downside of wallpaper, however, is that sometimes a pattern goes “out of style” after a certain number of years. A pattern you chose 15 years ago just may not work with modern décor. Homeowners who like to change the look of their homes from time to time tend to prefer painting for this reason. As an added benefit, it is also cheaper and easier to apply.If you have had it with your outdated wallpaper, it may sometimes be tempting to just paint over it for a fast change. However, most professionals will say that wallpaper should always be removed before painting.That being said, there are some cases where painted over wallpaper may be beneficial for you.For one, leaving the wallpaper in place will allow you to paint the walls quickly and easily without damaging the plaster or drywall beneath it. Proper preparation is important before you paint over your wallpaper to ensure the best results.Some Effective Tips:1. First secure the wallpaper.2. Replace&remove damaged sections.3. Add adhesive to loose pieces to minimize the chance the paper will fall.4. Add a thin line of clear caulk around the perimeter of the walls. At the joint seam where the paper meets the floor and ceiling.5. Prepare your walls carefully.6. With a thin coat of joint compound, cover heavily textured paper - It will help smooth out the surface so that the texture won’t show through the paint.8. Gently sand down the seams of the wallpaper so they are not as noticeable.Before painting apply a coat of oil-based primer to the entire surface of the walls - This helps seal the adhesive in the paper away from the moisture in the paint. Moisture from paint can often loosen wallpaper glue, causing bubbles or peeling.Now you are ready to make a decision about your walls.Enjoy Painting!!!
